Dell Inspiron 1525n (PP29L) LCD Hinge Removal Tutorial


In this Dell laptop tutorial we are going to show you how to install and replace the LCD Hinge on your Dell Inspiron 1525n laptop. These installation instructions have be made into 15 easy to follow printable steps. We have also create a video tutorial that shows you how to install your Dell Inspiron 1525n LCD Hinge.

Before you begin

Please take the time read the following safety guidelines when working on static sensitive electrical components.
Dell repair manual service precautions

Tools needed for this laptop repair

  • 1 x small phillips head screw driver
  • 1 x small plastic scribe
Inspiron 1525n HingeInspiron 1525n LCD Hinge

Video tutorial repair manual



Installation and Removal Instructions
Dell Inspiron 1525n LCD Hinge

Remove the battery.

Step 1

  • Remove the battery.
Access Door

Step 2

  • Access Door
  • Unscrew the 8 screws holding the Access Door Cover.
  • Remove the cover, starting from right to left.
Access DoorUnscrew the 8 screws holding the Access Door Cover.
WLAN Wireless Card

Step 3

  • WLAN Wireless Card
  • Unhook the antenna wires.
  • Remove the bottom display screws.
WLAN Wireless CardUnhook the antenna wires.
Power Button Cover

Step 4

  • Power Button Cover
  • Remove two 2mm x 3mm screws that hold the 1525/1526 center control power button cover to the base of the computer.
Turn the computer over (as if you were typing on it), and fully open the display (approximately 180 degrees, or as far as possible).

Step 5

  • Turn the computer over (as if you were typing on it), and fully open the display (approximately 180 degrees, or as far as possible).
  • Lift and unsnap the 1525/1526 center control power button cover using a small flat head screw driver or a plastic scribe from the backside of the computer, from right to left. (Be very careful removing it because the plastic can be fragile. (Use caution lifting the power button cover off of the laptop, a cable is attached beneath it that can break easily.)
Disconnect the media control cable under the power button cover and lift off the power button cover.

Step 6

  • Disconnect the media control cable under the power button cover and lift off the power button cover.
Keyboard Removal

Step 7

  • Keyboard Removal
  • Unscrew the (2) 2.5mm x 5mmscrews above the keyboard and gently lift up the keyboard to reveal the ribbon cable. Be careful lifting the keyboard because it is very easy to cause damage to the ribbon cable or the motherboard connector. (If the motherboard connector breaks, it is very hard to find replacements for them without replacing the entire motherboard.)
Lift the keyboard cable connector latch and remove the keyboard ribbon cable and keyboard.

Step 8

  • Lift the keyboard cable connector latch and remove the keyboard ribbon cable and keyboard.
LCD Display Assembly

Step 9

  • LCD Display Assembly
  • Unplug the display cable from the motherboard.
  • Unplug the camera cable from the motherboard.
LCD Display AssemblyUnplug the display cable from the motherboard.
Slide antenna wires out of the motherboard and loosen them from the top of the laptop.

Step 10

  • Slide antenna wires out of the motherboard and loosen them from the top of the laptop.
Unscrew the (2) 2.5mm x 3mm – 10 mm wafer hinge screws from the left display hinge.

Step 11

  • Unscrew the (2) 2.5mm x 3mm – 10 mm wafer hinge screws from the left display hinge.
  • Unscrew the (2) 2.5mm x 3mm – 10 mm wafer hinge screws from the right display hinge.
Unscrew the (2) 2.5mm x 3mm – 10 mm wafer hinge screws from the left display hinge. Unscrew the (2) 2.5mm x 3mm – 10 mm wafer hinge screws from the right display hinge.
Lift the 1525/1526 LCD display assembly up away from the base.

Step 12

  • Lift the 1525/1526 LCD display assembly up away from the base.
Remove the 6 rubber screw hole covers.

Step 13

  • Remove the 6 rubber screw hole covers.
  • Loosen the retaining screw in the corner of the display and remove the (5) 2.5mm x 4.5mm x 1.5mm display bezel screws.
Remove the 6 rubber screw hole covers. Loosen the retaining screw in the corner of the display and remove the (5) 2.5mm x 4.5mm x 1.5mm display bezel screws.
Unsnap the display bezel running you fingers under the edge of the bezel while lifting up. Do this carefully so the bezel doesn’t break and your fingers don’t get cut by sharp metal under the bezel.

Step 14

  • Unsnap the display bezel running you fingers under the edge of the bezel while lifting up. Do this carefully so the bezel doesn’t break and your fingers don’t get cut by sharp metal under the bezel.
Remove the (2) 2.5mm x 5mm screws that attach the LCD mounting rails to the hinges.

Step 15

  • Remove the (2) 2.5mm x 5mm screws that attach the LCD mounting rails to the hinges.
  • Remove the LCD screen from the back assembly.
Remove the (2) 2.5mm x 5mm screws that attach the LCD mounting rails to the hinges. Remove the LCD screen from the back assembly. Remove the (2) 2.5mm x 5mm screws that attach the LCD mounting rails to the hinges.
Inspiron 1525n HingeInspiron 1525n LCD Hinge

Topics: Dell Inspiron Repair Manuals Dell Laptop Repair Dell Repair Manuals Inspiron 1525n LCD Hinge

Join the conversation!

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.