Dell Latitude E6400 DC Jack with Cable Removal and Installation


In this Dell laptop tutorial we are going to show you how to install and replace the DC Jack with Cable on your Dell Latitude E6400 laptop. These installation instructions have be made into 27 easy to follow printable steps. We have also create a video tutorial that shows you how to install your Dell Latitude E6400 DC Jack with Cable .

Before you begin

Please take the time read the following safety guidelines when working on static sensitive electrical components.
Dell repair manual service precautions

Tools needed for this laptop repair

  • 1 x small phillips head screw driver
  • 1 x small plastic scribe
Latitude E6400 DC Jack

Dell Laptop Replacement Parts Needed

DIY Discount - Parts-People.com offers 5% off to all DO-IT-YOURSELFERS!
Use this coupon code to save 5% off these parts
DIYM514
Latitude E6400 DC Jack

Video tutorial repair manual



Installation and Removal Instructions
Dell Latitude E6400 DC Jack with Cable

Step 1

  • Slide the battery latches over and slide the battery up.
Slide the hard drive out of the laptop.

Step 2

  • Remove the (2) 3mm x 3mm hard drive screws.
  • Slide the hard drive out of the laptop.
Slide the hard drive out of the laptop. Remove the (2) 3mm x 3mm hard drive screws.
Press in the optical drive latch to get it to eject.

Step 3

  • Unscrew the 2mm x 3mm optical drive locking screw.
  • Press in the optical drive latch to get it to eject.
  • Pull the optical drive latch to slide the drive out of the laptop.
Press in the optical drive latch to get it to eject. Pull the optical drive latch to slide the drive out of the laptop. Unscrew the 2mm x 3mm optical drive locking screw.
Slide the door down and lift it off of the laptop.

Step 4

  • Loosen the access panel door cover screw.
  • Slide the door down and lift it off of the laptop.
Slide the door down and lift it off of the laptop.Loosen the access panel door cover screw.
Slide the memory out of the memory slot.

Step 5

  • Separate the clips on the left and right side of the memory stick until the memory pivots up to a 45 degree angle.
  • Slide the memory out of the memory slot.
Remove the 2mm x 3mm WWAN card screw.

Step 6

  • Disconnect the WWAN antenna cables.
  • Remove the 2mm x 3mm WWAN card screw.
  • Remove the WWAN card from the motherboard.
Remove the 2mm x 3mm WWAN card screw. Remove the WWAN card from the motherboard.Disconnect the WWAN antenna cables.
Remove the 2mm x 3mm WLAN card screw.

Step 7

  • Disconnect the WLAN antenna cables.
  • Remove the 2mm x 3mm WLAN card screw.
  • Remove the WLAN card from the motherboard.
Remove the 2mm x 3mm WLAN card screw. Remove the WLAN card from the motherboard.Disconnect the WLAN antenna cables.
Loosen the 4 heat sink screws.

Step 8

  • Unplug the fan.
  • Loosen the 4 heat sink screws.
Loosen the 4 heat sink screws. Unplug the fan.
Using a flat head screw driver, turn the CPU locking screw counterclockwise to unlock the CPU.

Step 9

  • Using a flat head screw driver, turn the CPU locking screw counterclockwise to unlock the CPU.
Installation note 2: Tighten the heatsink screws in the order listed on the heatsink.

Step 10

  • Installation note 1: Make sure to replace thermal compound or thermal pads on the CPU and heatsink.
  • Installation note 2: Tighten the heatsink screws in the order listed on the heatsink.
  • **This image is used only as an example.**
Under the battery, loosen the 3 clips by sliding them to the left.

Step 11

  • Under the battery, loosen the 3 clips by sliding them to the left.
Slide the hinge covers up and lift them off of the laptop base.

Step 12

  • Unscrew the (2) 2.5mm x 5mm screws on the left and right hinge covers.
  • Slide the hinge covers up and lift them off of the laptop base.
Slide the hinge covers up and lift them off of the laptop base.Unscrew the (2) 2.5mm x 5mm screws on the left and right hinge covers.
Remove the 2mm x 3mm WPAN card screw.

Step 13

  • Disconnect the WPAN antenna cables.
  • Remove the 2mm x 3mm WPAN card screw.
  • Remove the WPAN card from the motherboard.
Remove the 2mm x 3mm WPAN card screw. Remove the WPAN card from the motherboard.
Unscrew the (2) 2.5mm x x5mm hinge screws.

Step 14

  • Loosen the antenna cables and disconnect the LCD cable.
  • Unscrew the (2) 2.5mm x x5mm hinge screws.
Unscrew the (2) 2.5mm x x5mm hinge screws.Loosen the antenna cables and disconnect the LCD cable.
Unplug the DC jack cable.

Step 15

  • Unplug the DC jack cable.
Unscrew the (7) 2.5mm x 5mm palm rest screws on the bottom of the laptop.

Step 16

  • Unscrew the (7) 2.5mm x 5mm palm rest screws on the bottom of the laptop.
Lift under the LED cover to remove it from the laptop.

Step 17

  • Turn the laptop over and open it up.
  • Lift under the LED cover to remove it from the laptop.
Using the tab at the top of the keyboard, slide the keyboard up and lift the keyboard away from the laptop.

Step 18

  • Remove the (2) 2mm x 3mm screws.
  • Using the tab at the top of the keyboard, slide the keyboard up and lift the keyboard away from the laptop.
Using the tab at the top of the keyboard, slide the keyboard up and lift the keyboard away from the laptop. Remove the (2) 2mm x 3mm screws.
Disconnect the 4 palmrest cables.

Step 19

  • Disconnect the 4 palmrest cables.
Lift the palmrest off of the laptop base.

Step 20

  • Unscrew the (4) 2.5mm x 5mm palm rest screws on the top of the laptop.
  • Lift the palmrest off of the laptop base.
Lift the modem off of the motherboard.

Step 21

  • Remove the 2mm x 3mm modem screw.
  • Lift the modem off of the motherboard.
  • Unplug the modem cable.
Lift the modem off of the motherboard.Unplug the modem cable.
Remove the (2) 2mm x 3mm screws.

Step 22

  • Remove the filler card.
  • Remove the (2) 2mm x 3mm screws.
Remove the (2) 2mm x 3mm screws. Remove the filler card.
To remove the cage you will have to press down on the center of the cage and lift the back edge at the same time.

Step 23

  • To remove the cage you will have to press down on the center of the cage and lift the back edge at the same time.
Remove the protective tape.

Step 24

  • Unplug the 1394 cable.
  • Remove the protective tape.
Remove the protective tape. Unplug the 1394 cable.
Unplug the smart card cable.

Step 25

  • Unplug the smart card cable.
Carefully lift the motherboard out of the base, starting at the back. The USB/NIC circuit board will disconnect from the motherboard and stay in the base assembly.

Step 26

  • Remove the (3) 2.5mm x 5mm motherboard screws.
  • Carefully lift the motherboard out of the base, starting at the back. The USB/NIC circuit board will disconnect from the motherboard and stay in the base assembly.
Remove the DC jack and cable from the laptop base.

Step 27

  • Remove the DC jack and cable from the laptop base.
Latitude E6400 DC Jack

Dell Laptop Replacement Parts Needed

DIY Discount - Parts-People.com offers 5% off to all DO-IT-YOURSELFERS!
Use this coupon code to save 5% off these parts
DIYM514
Latitude E6400 DC Jack

Topics: Dell Latitude E6400 Repair Manual Dell Laptop Repair Dell Repair Manuals DC Jack Latitude E6400

Join the conversation!

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.